backup camera

Aug 18 2020

How to Connect a Relay for Car Reverse Camera Installation

When you are installing an aftermarket head unit upgrade with a car reverse camera, the rear view image on the display may be no signal, flickering, or a similar issue. This is most probably the voltage from your car reverse light is not stable, so it can not provide stable 12V voltage to the camera. Because the car rear view camera should be powered with 12V car reverse light. So that the camera can get 12V power from your reverse light.

If your car can not provide stable 12V voltage from reverse light to the camera, then the camera display will be no signal, or flickering. This is a common issue especially for some old cars. If you have a multi-meter, you can also measure the voltage from your car reverse light.

Solution is to connect a relay between the power source and the camera.

At first, you should know what a relay is, how does it look like, here’s a picture for your reference:

relay for reverse camera

How to connect a relay?

  1. Connect pin 30 (blue wire) to battery power source.
  2. Pin 87 (red wire) goes to camera power wire leading to head unit.
  3. Pin 85 (white wire) goes to reversing light power wire.
  4. Pin 86 (Black wire) to ground.

reverse camera and relay wiring diagram

Thanks our customer Gregory Davis who provided the above photo from USA. He solved the camera unstable issue by connected a relay.

part of the relay

Connected and tucked away in side storage panel.

relay connected

Thanks Lance from France who provided these photos and instruction for connecting the relay.

Tips for connecting a car rear view camera

Installing a car back up camera with an aftermarket head unit is not difficult for a professional mechanic. From the head unit side, you should connect 2 cables.

One is the video cable with RCA connector, but please pay attention to the label on the cable, because the RCA cables should come with other plugs which are also with RCA connector, the label may be written as “BACK VIDEO”, or “REVERSE CAMERA VIDEO”, if you have a doubt, do not hesitate to contact the supplier of your unit to confirm which is the video cable for the camera.

The other cable is a loose trigger wire, which triggers the camera to work after you put in reverse gear. It may be labelled with “REVERSE 倒车检测” or “BACK”. If your display can not automatically switch to backup images, you should check this loose trigger wire and see if you connect it correctly.

camera display cables

Got any questions about how to connect a reverse camera or a relay? You can write a comment below or drop us an email to sales@dvdgpsnav.com. Please provide as much information about your questions or your issue as possible, so we can better help you.

Last modified: August 18, 2020 By DVDGPSNAV Posted in backup camera • 0 • Tags: , , ,

Mar 4 2016

Car Trunk Lid Handle Back up Camera for BMW E46 E90 E39 E60 E70 F10 F30 E82 E88

What’s the best option if I want to install a back up camera for my BMW? Do I need to drill a hole? Does it look OEM? These are the questions which may ask for those who want to purchase and install the backup camera for BMW 3 series or 5 series like BMW E46, BMW E90, BMW E39, BMW E60, BMW E70, BMW F10, BMW F30, BMW E82, BMW E88,  BMW X1, BMW X5 and so on.

bmw trunk lid handle back up camera

As we all know, the universal reversing cameras are developed for all vehicles, for those universal ones, you may need to drill a hole from the rear position near the license plate, or you will need to drill 2 holes for screws fixing the camera. Besides, the universal one means it’s for every car, so it does not look oem or even ugly for your specific car.

Thanks to the modern technology, the trunk lid handle backup camera for BMW comes out now. Obviously the BMW trunk lid handle back up camera should be installed in the trunk handle, and the camera is hidden in the trunk handle, you are even not able to see it from the back of your BMW E90, BMW E60 or BMW F10. Unlike the universal ones, this BMW trunk handle rear view camera is easy for installation, you will not need to drill any holes, just fix it into your trunk lid handle, and it doesn’t replace your license plate light for night vision, you can check below picture showing how it looks like after installing:

Can this BMW trunk handle back up camera fit my car?

It’s easy to check if this BMW trunk lid handle backup camera fits your car by measuring the dimensions from the trunk handle, if the measurements are about 110x39mm as below:

110mm

39mm

You should choose the No.1 model which is with measurements of 110x39mm. While if your measurements are 162x47mm, No.1 model is the correct one. For more information about this reversing camera just visit: https://www.dvdgpsnav.com/bmw-trunk-handle-rear-view-camera.html

trunk handle rear view camera for BMW

 

Main Features:

HD CCD image sensor
520TV line
with parking lines
PAL/NTSC
170 degree viewing angle
Waterproof: IP 68
Price is only US$26.9.

 

Last modified: April 22, 2019 By DVDGPSNAV Posted in backup camera, BMW • • Tags: , , , , ,

How-to-install_Real_view_camera

May 8 2014

How to install the back up camera for Suzuki SX4

Recently we have a customer who installed a back up camera for Suzuki SX4, we appreciate our customers sharing his experiences when installed the camera and would like to share his experience with anyone who don’t know how to install it.  He has installed a suzuki sx4 dvd/gps unit and a back up camera for suzuki sx4 hatchback.

Below are his detailed instructions.

This is a ‘must have’ when buying the DVD/GPS unit. The connections are straight forward, but the install does take some time. First connect one end of the 15’ cable with an RCA plug (and RED wire) at both ends, to the RCA jack (CAMERA-AV-IN) on the unit. The RED wire connects to the BACK wire on the rear of the unit.

Next, lower the steering wheel and unsnap the cover on the left side of the steering wheel. Then fish the rest of the cable over to the left side cover. Then under the door sill cover, behind the floor seat-belt anchor, the rear door sill cover, up under the rubber molding on the back fender well. Then unhook the upper part of the cover over the little window behind the rear door. Fish the cable over to the rear hatch. Remove the cover on the inside of the hatch so wires and cables are visible. Rather than trying the impossible task of fishing the cable through the boot connecting the hatch to the car, I notched both ends of where the boot attaches. Then fish the cable up the left side of the hatch to where it will be available to plug into the rear camera. Next I took off the left tail light unit. Connect a 6’ wire to the red and black wires of the backup light. The other end will be fished up behind the little window to the backup camera. The black end of the wire will be connected to the black wire on the backup camera. The red end of the wire will be connected to the red wire on the end of the RCA plug AND the red wire from the backup camera.

To install the camera, remove the 4 nuts from the long cover over the license plate. Then unplug the license plate light.
NOTE: put some sort of tool in the loop where the hatch latches when closed…otherwise, you won’t be able to open the hatch with that light wire unplugged. Then remove the left light. (I did not reinstall the left license light.)
You’ll have to Dremel-alter the camera to fit in the license plate cover. This will take some time and patience. When it finally fits, reconnect the cover with the 4 nuts, replace the left tail light, and any covers that were loosened.

NOTE: All wires should be soldered and taped. Be careful when removing or replacing any covers or panels.
Once you have the backup camera functioning, you’ll wonder how you ever got by without it!

Though that’s a detailed installation instruction for the Suzuki SX4 back up camera, please install it carefully, if you are still not good at the installation, we suggest you asking a professional mechanic to do that for you.

Below is a picture showing you how to connect our BMW camera, including all wires connection, the wires connection are more or less the same as the Suzuki SX4 back up camera.

suzuki sx4 rear camera installation

More information about how to install a back up camera.

 

Last modified: January 3, 2019 By DVDGPSNAV Posted in backup camera, DVD/GPS Installation, Suzuki • • Tags: , , ,

Dec 31 2013

How to install a back up camera?

Have got a back up camera but don’t know how to install it? Don’t worry, with this post there are step-by-step instructions to install a reverse camera. Though installation is very easy for a professional mechanic, it do require some professional knowledge for installation, so if you still don’t know how to install the camera, we highly suggest you find a shop to install it for you.

If you need to connect the back up camera with a car dvd/gps unit, firstly you need to check the wiring diagram for the unit, the wiring diagram can be seen at the bottom of the unit if you got our dvd gps units. There’s a wire labelled with BACK, this wire is used to control reverse control, it should be connected with 12v reverse light power, if you did not connect this wire, the camera display can not switch automatically after you put in reverse gear. There’s also a cable to connect the backup camera from our RCA cables.

This wire labelled with BACK need to be connected with 12V+ reverse light power.

back

And this is the video cable to connect the camera, usually label with “BACK-VIDEO-IN” or “CAMERA-IN”.
cable

The installation guide for the rearview camera is as follows:

How to Install :

  1. Take out your stock license plate light at the back of your car.(don’t worry, nearly all cameras have night vision)
  2. Fix the camera to where the stock license plate light was.(some back up cameras need to drill a hole to fix it)
  3. Connect the built-in license plate light of the camera to where the stock license plate light was connected to get the power
  4. Connect the power of the camera to your reverse lights – red wire to positive and black wire to negative.
  5. Connect the video cable of the camera to the extension cord.
  6. Connect the extension cord to your car dvd gps monitor.
  7. You will see the images when your car is in reverse shift.

Wiring diagram for installation of the camera

car-rear-camera-wiring-diagram

After installation of the rear camera, if you found the rear view images displayed on the car DVD monitor was opposite, then you can check settings > Camera Mirror, change to Normal or L&R Mirror.

Common camera installation issue and how to solve

After installation of the backup camera, if your screen display no signal, or flickering, your backup video is not stable, that’s because your reverse light can not provide stable 12V voltage to the camera, you can add a relay to provide stable 12V power to the camera to fix this issue. For more information you can check this post: How to connect a relay for car back up camera?

Last modified: October 31, 2020 By DVDGPSNAV Posted in backup camera, DVD/GPS Installation • 0 • Tags: , , ,

back to top